-
When to use this checklist
-
Step 1: Lock out—and verify the right breaker
-
Step 2: Inspect the Bohn evaporator fan motor before you clean the coil
-
Step 3: Dry-clean the evaporator coil first, then wet-clean
-
Step 4: Check the air-cooled condenser—not just the evaporator
-
Step 5: Clear the drain pan and line—the most skipped step
-
Step 6: Verify defrost termination and heater operation
-
Step 7: Inspect refrigerant lines and insulation
-
Step 8: Ice machine specifics
-
Step 9: Document readings and photos before you leave
-
Common mistakes and what to watch for
When to use this checklist
This is for the person who signs off on refrigeration maintenance—the facility manager, the service manager, or the contractor doing the work. It covers walk-in coolers, freezers, and ice machines. Use it for seasonal changeovers, post-installation verification, or anytime a vendor hands you an invoice for "coil cleaning."
Nine steps. About 90 minutes for a single evaporator, longer if the coil hasn't been touched in a year. I've been reviewing this work since 2019, and the same things get skipped over and over. The steps below are the ones I actually check before I approve payment.
Step 1: Lock out—and verify the right breaker
Don't trust the panel label. I've seen a label that said "EVAP 3" controlling a condenser two rooms away. Kill the disconnect, tag it, and confirm with a meter before you touch anything.
This sounds basic. It's the step most often rushed when a tech is on a tight schedule.
Step 2: Inspect the Bohn evaporator fan motor before you clean the coil
Order matters here. If you clean first and the motor fails a week later, you're pulling the coil assembly apart twice. Check the motor first.
- Shaft play: Grip the blade and rock it. More than 1/16" of lateral movement means the bearing is going.
- Blade clearance: Spin it by hand. It should spin freely without scraping the shroud or the coil face.
- Amp draw: Compare against the nameplate. A motor drawing 10–15% over spec is on its way out, even if it's running.
- Mounting hardware: Loose motor mounts cause vibration, and vibration cracks coil tubes at the return bends. Check torque on the bracket bolts.
A Bohn evaporator fan motor that's drawing high amps but still running is a red flag. It's not saving you money to leave it in—it's borrowing time against a callback.
Step 3: Dry-clean the evaporator coil first, then wet-clean
This is the step where most techs start with a spray bottle of cleaner. Wrong order.
Dry-clean first: vacuum the coil face with a soft brush attachment, then comb the fins straight with a fin comb. If the fins are bent, airflow drops before you even start washing. On a Bohn evaporator with tighter fin spacing, bent fins on the entering-air side are the most common airflow restriction I find during audits.
Then apply cleaner, let it dwell per the label, and rinse. Rinse from the clean side toward the dirty side—otherwise you're pushing grime deeper into the coil.
Same principle applies whether you're cleaning a residential AC evaporator or a commercial unit. The fin comb and the rinse direction are the two steps people skip.
Step 4: Check the air-cooled condenser—not just the evaporator
If the system is a split or remote setup, the Bohn air cooled condenser gets half the attention and twice the dirt. Condensers sit outdoors or in mechanical rooms where dust, pollen, and cottonwood collect on the fin face.
Look for:
- Fins flattened on the intake side
- Debris matted between the coil and the fan guard
- Fan blade pitch and motor amp draw (same checks as Step 2)
- Head pressure readings before and after cleaning—document both
Bottom line: if you clean the evaporator and skip the condenser, you've fixed half the problem and reset the other half to fail.
Step 5: Clear the drain pan and line—the most skipped step
I'll be blunt: this is the step I find skipped more than any other. A clean coil on top of a clogged drain pan is a water leak waiting for the next humid week.
Pull the pan, scrub it, and flush the drain line with water and a shop vac. Check the slope. If the pan holds standing water after the flush, the line is partially blocked or the pitch is wrong.
We didn't have a formal drain-pan verification step in our service protocol back in 2021. It cost us when a contractor billed for six "full cleanings" and two of the walk-ins still had blocked pans. The spoiled product claim came to about $4,800, give or take. Now every work order includes a photo of the dry pan before sign-off.
Step 6: Verify defrost termination and heater operation
On freezers, the defrost cycle is where a "cleaning" turns into a callback if nobody checks it.
- Confirm the termination sensor reads correctly at temperature.
- Check heater resistance with a meter—don't rely on "it felt warm."
- Watch one full defrost cycle if you can. Most techs don't, and that's where intermittent failures hide.
Step 7: Inspect refrigerant lines and insulation
Look for oil residue at braze joints (a sign of a slow leak), cracked suction-line insulation, and rubbing where lines pass through the cabinet. Per EPA Section 608 requirements, any technician handling refrigerant needs proper certification—but the visual inspection doesn't require handling anything. It's just looking.
Step 8: Ice machine specifics
Ice machines get their own pass because the failure mode is different. Scale, slime, and condenser dust are the big three.
- Clean the condenser on air-cooled ice makers every 3–6 months in dusty environments.
- Descale the evaporator per the manufacturer's schedule—not "when production drops."
- Check the water filter change date. A clogged filter stresses the machine quietly.
For two seasons I went back and forth between doing ice machine cleaning in-house versus putting it on the refrigeration contractor's scope. In-house gave us speed and lower cost per visit. The contractor gave us documented descaling logs and warranty-friendly records. Ultimately went hybrid: in-house does the monthly rinse, contractor does the quarterly descale and logs it. Should have split it that way from the start.
Step 9: Document readings and photos before you leave
This is the step that protects everyone. Record:
- Before/after amp draw on each fan motor
- Before/after head pressure (condenser jobs)
- Superheat or subcooling if you adjusted charge
- Photo of clean coil face, dry drain pan, and nameplate
So glad I started requiring amp readings on fan motor invoices. On one batch of eight motors, three were drawing 15% over nameplate—would have failed within a month. The contractor swapped them under the parts warranty before they ever tripped an overload. That was one signature away from being our problem instead of theirs.
Common mistakes and what to watch for
Cleaning the coil but not the pan. Already covered, but it bears repeating. The pan is the cheapest part of the job and the most common callback.
Replacing a fan motor without checking blade clearance. A new motor with a warped blade will fail the same way the old one did. Check the blade before you bolt on the replacement.
Using coil cleaner on a dry coil without rinsing the drain path first. Cleaner residue plus dust equals a clogged drain faster than dust alone.
Skipping the condenser because it's "in a mechanical room." Mechanical rooms are dustier than outdoors. It counts.
Accepting "cleaned" without a photo. If your service provider can't produce a before/after photo of the coil face and the drain pan, you're paying for a visit, not a cleaning.
And one more: if a contractor tells you they can handle the coil cleaning, the fan motor replacement, the refrigerant charge adjustment, the electrical troubleshooting, and the controls calibration—all on the same visit, on any brand—ask them what they're actually best at. In my experience, the vendor who says "we're strong on mechanical service, but for controls you want a specialist" is the one I trust with the rest of the scope.